ztc zt188 restart solved

here is pinout from pinfinder

software version: 1.06
cable type: 1x8 (L8A)
platform: MT6205, MT6217-MT6228
searching adapter at COM7...
adapter found, version: 2000
pins: 8, plain
power cycles: 1
activation cycles: 7
power-off delay: 20
start Rx/Tx: 1/1
Loading configuration...
Initializing...
Press and HOLD phone Power button now !
detecting pins...
19200
CPU: MT6225
result: Rx:3 Tx:4
time required: 10 sec
Power On !




COM7 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: reset
Boot...
Press and HOLD Power button now !
baud autodetection active
19200 autodetect
Connecting, wait...
Initializing[6225:8A03:8A00]...
CPU: MT6225
high speed boot enabled
chip: 0001:E103:000D
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
115200
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\id.4F1E8253.[MT6225_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_08_MP_V27.BIN_491ED62D].rpl
identification#1 detection finished
device-id: 4F1E8253
identification#1 protocol ver: 04
ver. sw1: MT6225_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_08_MP_V27.BIN
ver. sw2: MAUI.06B.W07.08.MP.V27, D229E1B6
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: 01227E22202200:18E59F00000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom[MT6225_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_08_MP_V27.BIN]]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_eeprom[MT6225_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_08_MP_V27.BIN]_20080330-110944.B0E.bin
flash: 01227E22202200:18E59F00000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
Write Done
Finalization...
formatting...
flash: 01227E22202200:18E59F00000000
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log_4F1E8253_MT6225_06B_PCB01_GPRS_MT6225_S00.MAUI_06B_W07_08_MP_V27.BIN_491ED62D_20080330-111013.B0X.bin
Finished, time used: 268 sec
Remove/Install battery now !

File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !

Good work keep it up